## Introduction

The longitudinal strength of a vessel is integral to its evaluation for a given purpose. To get an introduction to the topic, please refer to our other article

https://thenavalarch.com/longitudinal-strength-ships-introduction/

In this article, we’ll see from a regulatory (Classification) perspective, what the important factors determining Longitudinal Strength requirements for barges are.

Longitudinal Strength determines the global strength characteristics of the Barge. Referring to our previous article, considering the ship as a simply supported beam, the strength will depend on the strength of the structural cross-section of the ship. Most of the time, the midship structural section is considered the representative for the barge’s strength as the maximum bending moment is expected at midship.

A midship section of a Barge is shown below:

Also, a typical bending moment diagram of a barge is shown below:

We can see that the midship section is the critical one since the bending moment amidships is the largest

What parameter determines the strength of the midship section of the Barge?

## Beam analogy

Considering the beam analogy, the strength of the beam depends upon the section property of the beam. In short, the bending stress on the beam is given by:

**Bending Stress = Bending Moment/Section Modulus**

Thus, the defining parameter that dictates the beam’s strength is its Section Modulus.

How do we calculate the Section Modulus of the midship section (or any other section) of the ship?

The calculation of section modulus is investigated in another related article:

https://thenavalarch.com/how-to-calculate-the-strength-of-midship-section-of-a-ship/

## The role of Classification Rules

Once we have calculated the section modulus of the midship section of the Barge, how do we know if it is sufficient? How do we know what should be the minimum section modulus for the Barge to be fit to ply in the open ocean?

The requirements for minimum strength characteristics are provided by regulatory bodies (a.k.a. Classification Societies like ABS, DNV, LR, IRS, CCS, etc.)

In this article, we’ll see from a regulatory perspective (i.e., Ship Classification) the requirements for longitudinal strengths of Barges.

We will refer to the American Bureau of Shipping (ABS) Rules for Building and Classing Steel Barges, 2020 for this article. It is to be noted that these rules apply to ocean-going barges with a Breadth-to-Depth ratio of up to 4.

The Classification rules help by providing the minimum requirements that the vessel must meet.

With regard to the longitudinal strength of Barges, the two important parameters that the rules have laid out are:

- Minimum Section Modulus amidships
- Minimum Hull girder moment of Inertia amidships

## Minimum Section Modulus amidships

The minimum section modulus requirement is specified in the American Bureau of Shipping (ABS) Rules for Building and Classing Steel Barges, 2020, Part 3, Ch.2, Section 1, 3.1

The required Section Modulus amidships (SM_{R}) is given by

*SM _{R} *

**=**

*K SM*_{b}where

**SM _{b} = C_{1}C_{2}L^{2}B (C_{b} + 0.7) cm^{2}-m (in^{2}-ft)**

- C
_{1}is a coefficient dependent of the length of the barge, and is higher or longer vessels - C
_{2}is a constant (0.01) - K = 0.629 + M
_{s}/(f_{p}SM_{b}) but is not to be taken less than 1.0

M_{s} = maximum still-water bending moment in the governing loaded or ballasted condition in kN-m (tf-m, Ltf-ft). When still-water bending moment calculations are not submitted, K will be taken as 1.0.

- f
_{p}= 17.5 kN/cm^{2}(1.784 tf/cm^{2}, 11.33 Ltf/in^{2})

## The factor K

As highlighted earlier, the bending stress on the midship section is given by

**Bending Stress = Bending Moment / Section Modulus**

Putting it the other way round,

**Section Modulus = Bending Moment/Bending Stress**

Thus, if we know the maximum bending moment that the vessel experiences and we know the limit of the bending stress of the material used, we can find out the minimum section modulus that the vessel requires.

The maximum still water bending moment that the vessel experiences can be obtained from the stability booklet, in which the full-load and ballast conditions, including any additional condition (critical in terms of long strength), are included. The highest still water bending moment of all these conditions is used for the calculation of K. When bending moment calculations are not available, K is to be taken as 1.

The still water bending moment (SWBM) calculations are mandatorily required to be submitted if the Barge is of length 76 m or more.

f_{p} is simply the allowable bending stress of the material used and translates to 175 MPa for mild steel, which is 75% of the yield strength of steel.

## Minimum Section Modulus amidships

The moment of inertia amidships is derived from the required section modulus, and is given by (Ref [1], 3-2-1, Sec 5):

*I ***= 0.03 SM_{R}L cm^{2}-m^{2} (in^{2}-ft^{2})**

where

*L *= length of the barge as defined in 3-1-1/3

*SM** _{R}* = hull girder section modulus required for the barge per 3-2-1/3.1, in cm

^{2}-m (in

^{2}-ft)

## High Strength Material

The above rules are applicable to the case when the hull material is Mild Steel. If high strength materials are used for either the upper or lower flanges of the hull girder or both, then a reduction factor is used in the calculation of the required Section Modulus (Ref [1], 3-2-1, Sec 11.3):

*SM _{hts} *

**=**

*Q*(*SM*)_{R}where

*Q *= 0.78 for H32 strength steel

*Q *= 0.72 for H36 strength steel

H32, H36 = as specified in Section 2-1-3 of the ABS *Rules for Materials and Welding (Part 2)*

## Wave Bending Moment

Besides the still water bending moment, the vessel also experiences Wave Bending moment in seas. The wave bending moment is considered when there are additional buckling calculations to be submitted to verify the scantlings of the vessel. To account for the wave bending moment in calculations of the factor K, the bending moment used is

**Bending moment = Still Water Bending Moment + Wave Bending Moment**

The formula used for wave bending moment is

Wave bending moment = S_{w} x SM_{b}, where S_{w} = 11.0 kN/cm2, or 110 MPa.

Considering the above, the formula for K becomes

**K = 0.629 + (S _{w} x SM_{b} + M_{S})/(f_{p} x SM_{b}) = 0.629 + {S_{w}/f_{p} + M_{s}/(f_{p} x SM_{b})}**

Thus, it is important to calculate the K factor accurately in order to get a reliable value for the required section modulus for the vessel.

That sums up this article about using Class rules to assess the longitudinal strength of Barges. The required section modulus is an important starting point to design the structural section of the vessel by selecting the right strength elements.

## References

[1] ABS RULES FOR BUILDING AND CLASSING STEEL BARGES, JULY 2020

[2] ABS *Rules for Materials and Welding (Part 2), July 2020*

*Disclaimer: This post is not meant to be authoritative writing on the topic presented. thenavalarch bears no responsibility for the accuracy of this article, or for any incidents/losses arising due to the use of the information in this article in any operation. It is recommended to seek professional advice before executing any activity which draws on information mentioned in this post. All the figures, drawings, and pictures are property of thenavalarch except where indicated, and may not be copied or distributed without permission.*

## A simplified method of performing fatigue analysis of offshore structures

A simplified method of performing fatigue analysis of offshore structures Introduction An offshore structure is subject to environmental loads of waves, wind and current. By their nature, the resulting wave loads on the structure are cyclical. These cyclical...

## How to use a ship’s hydrostatics to calculate its draft and trim

Introduction A ship’s hydrostatics, or hydrostats, is an oft used term in maritime parlance, and it refers to the characteristics when it is floating. What characteristics are these? How are these determined, and how can we read and understand them? Understanding...

## Numerical integration methods for hull volume estimation

Introduction The hull of a ship is a complex 3D geometry, and finding out its simple properties like volume, centroid, etc. is not possible through simple formulae unlike standard shapes like cuboid or a cylinder. How do we find a property, say the volume of a...

## How to do rule-based fitting calculations of a keyless propeller

Introduction A keyless propeller, as the name implies, requires no key for fastening the propeller on the cone of the propeller shaft. How is the torque then transferred to the propeller? The torque is transferred by the friction between the propeller and the...

## Designing Fillet Welds for Symmetrical Joint Sections

Introduction Fillet welds are the most commonly used weld types in marine structures. A fillet weld is used when there are two pieces of metal that are joined perpendicular to each other or at an angle. In this article, we will explore how to select the right size...

## Designing a stanchion/stopper for sea-fastening of deck cargo

Introduction Stanchions – a familiar term for mariners and ship designers. What are Stanchions? A stanchion is generally a vertical pipe or beam which is used to support some structural item or provide support rails on the deck. In ships, the most common type of...

## Designing bolts for a joint connection

Introduction Bolts are very commonly used fastening items and used in a variety of configurations. In this article, we will explore in-depth the design of a bolt used in connecting two members at a joint (bolted joint). We'll see what properties of the bolt are...

## Draft Surveys: Methodology, Calculations, and common errors

Introduction Marine transport is the backbone of the global trade and reasonably can be considered to be the artery of the global manufacturing supply chain, as more than four fifths of the world merchandise trade by volume is carried by sea. Undoubtfully, the...

## The Bulbous Bow – types, characteristics, and effects

This is Part 2 of the two-part series on Bulbous Bows. For Part 1, click here By Tamal Mukherjee, *This article originally appeared in May 2019 edition of Marine Engineers Review (India), the Journal of Institute of Marine Engineers India. It is being...

## The why and how of freeboard calculation of a ship

Introduction Freeboard is a common term used in vessel operations. Freeboard is the smallest vertical distance between the waterline and the freeboard deck (generally the upper deck) along the length of the vessel. The term ‘smallest’ is of significance, as the height...

Nice content. There is need to understand the first principles first to appreciate every parameter and models highlighted in this article. Thank you for putting this together.